|
|
We are proud to
announce the arrival of Audio-Technica turntable Cartridges to our line
of high quality audio accessories. Their turntable Cartridges have long
been recognized as some of the best quality available while still being
one of the most affordable in the industry.
We are an "Authorized" Audio-Technica dealer, and there
is a difference!
|
|
|
NEW
-THE ULTIMATE-
AUDIO-TECHNICA
"DUAL MOVING COIL"
TURNTABLE CARTRIDGE
AT33EV
AT33EV
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
STEREO OR
QUADRAPHONIC
for sale
The Top of the Line in their current line of high quality turntable
cartridges. If you are looking for the best from
Audiotechnica
and have a "moving coil" compatible pre-amp, then
here you go. Features "MicroLine" cut Nude Diamond
(allows for least record wear and most groove contact) with specially
cut Square Shank mounted to a Tapered Alloy tube cantilever.
Utilizes Audio-Technicas' own Vector-Aligned dual
coil design for
sonic generation.
The new half-inch standard mount .3 x .7 mil elliptical
AT33EV cartridge features a tapered duralumin cantilever. Dual Moving
Coil cartridge design increases channel separation and extends the
frequency response range delivering extraordinary audio quality.
Internally constructed with neodymium magnet for enhanced magnetic
energy and PCOCC wire for pure audio signal
transmission.
Specs are as follows:
- Dual "Moving Coil" design
- Elliptical Nude Diamond, cut @ 0.3 x 0.7 mil
- Cantilever:
Duralumin tapered pipe
- Frequency Response: 15-50kHz
- Output: 0.3mV
@ 1 kHz, 3.54 cm/sec
- Channel Separation: 30dB @ 1 kHz
- Channel Balance:
0.5dB @ 1 kHz
- Coil impedance:
10
Ωat 1 kHz
- Coil inductance: (mμH,
1 kHz) : 22
- Dynamic compliance: (x10-6 cm/dyne) : 10
- Static compliance: (x10-6 cm/dyne) : 40
- Direct current resistance: 10 Ohms
- Vertical Tracking Angle: 23°
Recommended Vertical Tracking Force:
1.8-2.2 grams (2.0 grams standard)
Recommended loading impedance: 100 ohms (with
head amplifier connected)
- Dimensions (mm); L16.6x
W 16.0 x H 26.5
Weight (g): 6.9
Again if you are looking for the ultimate sounding cartridge
from Audio Technica, for listening
to or for recording your vinyl collection and your record
collection is in excellent shape and you want to insure it stays that way
this is probably the cartridge for you. This is also
a great cartridge for decoding Quadraphonic LP's. Again, this is a
"moving coil" cartridge, so you will need a moving coil "head amp" or MC
setting on your stereo pre-amp or receiver.
AUDIO-TECHNICA AT33EV
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Your
price $659.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
Note: Moving coil
cartridges require receivers or preamps with compatible inputs; their
stylus assemblies are not field-replaceable.
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
DUAL "MOVING MICRO-COIL"
TURNTABLE CARTRIDGE
AT-OC9ML/II
ATOC9ML/II
ATOC9MLII
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
STEREO OR
QUADRAPHONIC
for sale
Great quality, Dual Moving "Micro-Coil"
turntable cartridge. Features "MicroLine" cut Nude Diamond
(allows for least record wear and most groove contact) with specially
cut Square Shank mounted to a Gold Plated,
Boron tube cantilever.
Utilizes Audio-Technicas' own Vector-Aligned dual
MicroCoil design for
sonic generation.
Moving coil cartridge with polished elliptical diamond tip, for the best in
clarity, transparency, precise stereo imaging, lower distortion and extended
vinyl life. A-T Vector-Aligned design, with two moving coils mounted at 90
degrees in place of the two moving magnets.
Specs are as follows:
- Dual "Moving Micro-Coil" design
- Stylus (needle) Shape: "MicroLine"
- Elliptical Nude Diamond, Square Shank cut @ 0.3 x 0.7 mil
- Cantilever:
Gold Plated, Boron Tube
- Frequency Response: 15-50kHz
- Output: 0.4mV
@ 1 kHz, 5 cm/sec
- Channel Separation:
31/21dB @
1 kHz/ 10 kHz
- Channel Balance:
1.0dB @ 1 kHz
Recommended Vertical Tracking Force:
1.25-1.75
grams
Recommended loading impedance: 20 ohms (with
head amplifier connected)
- Dynamic compliance: (x10-6 cm/dyne,
100Hz) : 9
- Static compliance: (x10-6
cm/dyne) : 35
- Vertical Tracking Angle: 23°
Weight (g): 8.0
Again if you are looking for a fabulous sounding cartridge
from Audio Technica, for listening
to or for recording your vinyl collection and your record
collection is in excellent shape and you want to insure it stays that way
this is probably the cartridge for you. This is also
a great cartridge for decoding Quadraphonic (sometimes
misspelled as 'quadriphonic') LP's. Again, this is a "moving
coil" cartridge, so you will need a moving coil "head amp" or MC setting on your
stereo pre-amp or receiver.
AUDIO-TECHNICA
ATOC9ML/II
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $559.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
Note: Moving coil
cartridges require receivers or preamps with compatible inputs; their stylus
assemblies are not field-replaceable.
|
NEW
AUDIO-TECHNICA
DUAL "MOVING MAGNET"
TURNTABLE CARTRIDGE
AT-150
AT150MLX
AT150MLX
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for
sale
Great quality, Dual Moving Magnet
turntable cartridge. Features "MicroLine" cut Nude Diamond
(allows for least record wear and most groove
contact) with specially cut Square Shank mounted to a
Gold Plated, Boron tube cantilever. Utilizes Audio-Technicas' own
Vector-Aligned dual magnet design for sonic generation.
MicroLine® shaped diamond tip. Vector-Aligned cartridge for outstanding
channel separation, very low distortion and superb tracking. Gold-plated
boron cantilever provides an extremely rigid yet lightweight platform.
PCOCC wire; mu-metal shielding plate.
Specs are as follows:
- Dual "Moving Magnet / Iron" design
- Elliptical Nude Diamond, Squard Shank cut @ 0.3 x 0.7 mil
- Stylus (needle) Shape: "MicroLine"
- Cantilever: Gold Plated Boron
- Frequency Response: 10-30kHz
- Output:
4mV @ 1 kHz, 5
cm/sec
- Channel Separation:
30/20dB @ 1 kHz/ 10 kHz
- Channel Balance:
0.8dB @ 1 kHz
- Recommended Load Capacitance: 100 – 200 pF
- Wire Used For Coils: PCOCC
- Coil impedance:
2.3K ohms at 1 kHz
- Coil inductance: (mH, 1
kHz) :
350
- Dynamic compliance: (x10-6
cm/dyne, 100Hz) : 10
- Coil direct current resistance: 530Ω
- Load resistance: 47kΩ
- Load carrying capacity:
100-200pF
- Static compliance: (x10-6
cm/dyne) : 40
- Recommended Vertical Tracking Force:
.75-1.75 grams
- Vertical Tracking Angle: 23°
- Recommended loading impedance:
47k ohms
- Dimensions (mm); L17.3 x W
17.0 x H 28.2
Weight (g): 8.3
Again if you are looking for a fabulous
sounding cartridge
from Audio Technica, for listening to
or for recording your vinyl collection and your record collection
is in excellent shape and you want to insure
it stays that way this is probably the cartridge for you.
AUDIO-TECHNICA AT150MLX
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply
priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Your
price $479.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
DUAL "MOVING MICRO-COIL"
TURNTABLE CARTRIDGE
AT-F3III
ATF3III
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
STEREO OR
QUADRAPHONIC
SORRY, NOW DISCONTINUED
-
The AT-F3III stereo cartridge provides excellent
all-around performance for those seeking an entry-level moving coil cartridge.
Featuring Audio-Technica’s dual coil design and elliptical stylus
(needle) (0.2 x 0.7
mil), the AT-F3III comes finished in a stylish silver
and blue housing. The stylus tip is mounted on an aluminum pipe cantilever in
order to achieve lighter weight. The elliptical stylus has two radii, the front
radius being wider than the side radius. This allows the stylus to ride in the
center of the groove, while the smaller side radius can more accurately track
higher frequencies. Due to it's super wide frequency
response, it is not only suitable for standard 'Stereo' use, but also works well
for playing 'Quadraphonic'
(sometimes misspelled as 'quadriphonic')
albums.
Specs are as follows:
Cartridge Design:
Dual "Moving-Coil", Standard 1/2" mount design
Stylus Type: Elliptical Nude Diamond, cut @ 0.2 x 0.7 mil
Cantilever:
Aluminum Tube
Frequency Response: 15-50kHz
Output voltage:
0.35 mV (1 kHz, 5 cm/sec.)
Channel Separation:
27dB @
1 kHz
Channel Balance:
1.5dB @ 1 kHz
Recommended Vertical Tracking Force:
1.8-1.2
grams
Recommended loading impedance: 100 ohms (with
head amplifier connected)
Again if you are looking for a fabulous sounding cartridge
from Audio Technica, for listening
to or for recording your vinyl collection and your record
collection is in excellent shape and you want to insure it stays that way
this is probably the cartridge for you. This is also
a great cartridge for decoding Quadraphonic LP's. Again, this is a "moving
coil" cartridge, so you will need a moving coil "head amp" or MC setting on your
stereo pre-amp or receiver.
AUDIO-TECHNICA
AT-F3III
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
SORRY, NOW DISCONTINUED
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
Note: Moving coil
cartridges require receivers or preamps with compatible inputs; their stylus
assemblies are not field-replaceable. |
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-440MLa
"PURPLE"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for sale
If you are looking a great, moving magnet, without breaking
the bank, from
Audiotechnica
here you go. Features "MicroLine" cut Nude Diamond
(allows for least record wear and most groove contact) with specially
cut Square Shank mounted to a Tapered Alloy tube cantilever.
Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for
sonic generation.
Specs are as follows:
- "MicroLine" cut, Nude, Square Shank Diamond
0.12 mil
stylus
- Tapered alloy tube Cantilever
- Frequency Response: 20-20kHz
- Output is a strong 4.0 (mV, 1 kHz, 5 cm/sec)
- Channel Separation; 27 (dB
at 1 kHz)
- Channel Balance;
0.8 (dB at 1 KHz)
- Coil impedance : 3,200 ohms at 1 kHz
- Coil inductance (mH, 1 kHz) : 490
- Dynamic compliance (x10-6 cm/dyne) : 10
- Static compliance (x10-6 cm/dyne) : 40
- Dimensions (mm) : L17.3 x W 16.0 x H 28.0
Weight (g) : 6.5
- Recommended Vertical Tracking Force 1.0-1.8 grams
(1.4 optimal)
- Recommended loading impedance 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
Again if you are looking for the one of the best sounding cartridges for listening
to and especially for recording your vinyl collection and your record
collection is in good shape and you want to insure it stays that way
this is probably the cartridge for you. Yes it's more expensive than
most (although it's not uncommon for cartridges to cost up into the
$1000-$2000 range and they can go as high as $15,000), but when compared to the time spent recording,
listening to and caring for your albums overtime it's a good and
reasonable investment. You won't be disappointed.
AUDIO-TECHNICA
AT-440MLa
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $289.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
ATP-2XN
PROFESSIONAL / DJ / COMMERCIAL USE
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
ALSO FOR PLAYING 78 RPM RECORDS!
COMES WITH AN EXTRA STYLUS TOO!
for sale
Audio Technica's commercial / pro series, Moving Magnet line of high quality
turntable cartridges. Designed for any speed records,
16, 45, 33 1/3 or 78 RPM records. This is our only one designed for
78 RPM records. If you are looking for the most
durability, or your records aren't in the best shape and you're having a
problem tracking heavy enough for some of them, or your table tracks heavy
by design, then here you go.
This is also a great 'high mileage' cartridge for
doing lots of vinyl to CD / Hard disc transfers or for a 'media transfer
biz'.
Features elliptical cut
bonded Diamond
(allows for least record wear and most groove contact) with
0.4 x 0.7 cut round
Shank mounted to a Super Heavy, Alloy tube cantilever.
Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for
sonic generation.
Specs are as follows:
Frequency Response:
15-22,000 Hz
Channel
Separation:
23/17 (dB at
1 kHz/10 kHz)
Recommended Vertical Tracking Force:
3.0-5.0
grams
Stylus (needle) Construction:
Bonded
Diamond to round
shank
Recommended Load Impedance:
47,000 ohms
Output:
a strong
5.3 mV (at 1 kHz, 5 cm/sec)
Channel Balance:
1.5 dB
Stylus Shape:
0.4 x 0.7
mil elliptical
Cantilever:
Alloy tube
Mount: Half-inch
Replacement Stylus (needle):
ATP-N2
(an extra new one included!)
If you are looking for a cartridge
to for DJ or Heavy duty commercial / Professional
applications, or your records are a bit "beat" and you need heavy
tracking, or you wish to listen to 78's on your "good" table, then this is
the cartridge you need. It's made to be abused! Yes it's more expensive than
most (although it's not uncommon for cartridges to cost up into the
$1000-$2000 range), but when compared to the time spent recording,
listening to and caring for your albums overtime it's a good and
reasonable investment. You won't be disappointed.
AUDIO-TECHNICA
ATP-2XN
NEW
These
are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply
priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $159.99
(with extra new stylus (needle) included)
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
TURNTABLE CARTRIDGE
AT-120E/T
"ORANGE"
1/2" STANDARD MOUNT
OUR MOST POPULAR
MODEL!
for sale
Superior performance in their current Moving Magnet line of high quality
turntable cartridges. If you are looking for outstanding performance from
Audio-Technica, but still keeping the price under a hundred bucks, then here you go. Features
Elliptical cut Nude, 0.3 x 0.7 mil., round shank Diamond mounted to a Alloy tube cantilever.
Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for
sonic generation.
Specs are as follows:
Cartridge Design: Moving Magnet,
Standard 1/2" mount design
Stylus (needle) Type:
Elliptical Nude Diamond / Elliptically cut @ 0.3 x 0.7 mil
Frequency Response: 15-25kHz
Output voltage: a strong 5 mV @ 1kHz
- Recommended Vertical Tracking Force 1-1.8 grams
Recommended loading impedance: 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
Again if you are looking for an incredible sounding cartridge for listening
to and especially for recording your vinyl collection and your record
collection is in good shape and you want to insure it stays that way,
this is probably the cartridge for you. Yes it's a bit more expensive than
many (although it's not uncommon for cartridges to cost up into the
$1000-$2000 range), but when compared to the time spent recording,
listening to and caring for your albums overtime it's a good and
reasonable investment. You won't be disappointed.
AUDIO-TECHNICA
AT-120E/T
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
$144.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
90 day full-price upgrade available on this model.
*(See
below for details)
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
TURNTABLE CARTRIDGE
AT-95ELC
AT95E
"GREEN"
1/2" STANDARD MOUNT
for sale
Finally, a replacement for the long-running AT-71ELC
'Green'. The Audio-Technica AT-95E. Will fit turntables requiring a standard
mount cartridge. Another great performing cartridge offering better
performance, but keeps the wallet happy. Features a Bonded Elliptical
0.4 x 0.7 mil Diamond stylus (needle) for better than average groove tracking.
Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for
sonic generation. Since the AT-95E has an
elliptically cut diamond stylus it will "blow away" it's slightly cheaper
counterparts, the AT70L / AT-70L and CN5625AL (AT-70L is now
discontinued anyway) with their "Close-n-Play" / Toy style "Conical"
cut stylus'! It is imperative to at least have a good elliptically cut
diamond for accurate
sound and lower record wear.
Specs are as follows:
Cartridge Design:
Moving Magnet, Standard 1/2" mount design
Stylus Type: Elliptically cut Bi-Radial @ 0.4 x 0.7 mil
Diamond Stylus
Cantilever: Alloy Tube
Frequency Response: 20-20kHz
Output voltage: 3.5 mV ( 1 kHz, 5 cm/sec)
Channel Separation: >20dB at 1 kHz
Channel Balance: <2dB at 1 KHz
Recommended Vertical Tracking Force: 1.5-2.5 grams
(2.0 recommended)
Recommended loading impedance: 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
The half-inch standard mount AT95E phonograph cartridge offers
outstanding clarity and detail. Reviewers have rated this affordable,
high-performance cartridge as a best buy value. Manufactured to Audio-Technica's
renowned quality standards, each cartridge is meticulously assembled with
remarkably tight tolerances. The elliptical diamond stylus is designed to track
record grooves with high accuracy for outstanding audio reproduction. Includes
mounting hardware and stylus guard.
If you are looking for a decent sounding cartridge for listening to your
albums, but not so much recording and your budget will not bear the cost of the
AT-440MLa or the AT-120E/T then this would make a nice sounding
cartridge for your 1/2" mount turntable.
AUDIO-TECHNICA
AT-95E
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
$69.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
90 day full-price upgrade available on
this model. *(See
below for details)
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT311EP AT-311EP
AT 311EP
UNIVERSAL
1/2" OR P-MOUNT
TURNTABLE CARTRIDGE
for sale
The Audio-Technica AT-311 EP. Will fit
turntables requiring either a P-mount or 1/2" standard mount cartridge. A
great performing cartridge offering above average performance with-out
breaking the bank. Features an
Elliptical 0.3 x 0.7 mil Bonded-Diamond stylus
(needle) for exceptional groove tracking.
Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for
sonic generation. The AT-311EPOT has a finer
elliptical cut to the diamond stylus than it's slightly cheaper counterpart, the
AT-301EP / AT301EP and since it has an elliptical cut, will "blow away" the
AT300P / AT-300P with it's "Close-n-Play" / Toy style "Conical" cut! At least a
good elliptical cut is imperative to accurate sound and lower record wear.
Specs are as follows:
- Elliptical Nude Diamond Stylus
- Elliptically cut Bi-Radial @ 0.3 x 0.7 mil
- Frequency Response: 15-27kHz
- Output is a high 5 mV @ 1kHz=
- Thin-Wall Cantilever
- Recommended Vertical Tracking Force 1.0-1.5 grams
- Vertical Tracking Angle 20
°
- Channel Balance = 1.25
- Channel Separation; 29dB @ 1kHz & 18dB @ 10kHz
- Recommended loading impedance 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
- Load Capacitance 100-200 pF
If you are looking for a much above average sounding cartridge for listening
and / or recording your vinyl, cartridge then this would make a very nice sounding
unit for your
1/2" or P-mount turntable.
AUDIO-TECHNICA
AT-311EP
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $64.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
90 day full-price upgrade available on this model.
*(See
below for details)
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-92ECD AT-92ECD
AT92ECD
UNIVERSAL
1/2" OR P-MOUNT
TURNTABLE CARTRIDGE
for sale
The Audio-Technica AT-92E. Will fit turntables requiring either a
P-mount or standard mount cartridge. Another great performing cartridge
offering above average performance with-out breaking the bank. Features
a Bonded Elliptical 0.3 x 0.7 mil Diamond stylus for exceptional groove
tracking. Utilizes Audio-Technicas' own Vector-Aligned dual magnet
design for sonic generation. The AT-92EPOT has a
finer elliptical cut to the diamond stylus than it's slightly cheaper
counterparts, and since it has an elliptical cut, will
"blow away" the AT300P / AT-300P with it's "Close-n-Play" / Toy style "Conical"
cut! At the very least, a good 'elliptically cut diamond' is imperative to accurate sound and lower
record wear.
Specs are as follows:
- Frequency Response: 15-27kHz
- Output 3.5 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-1.5 grams
- Recommended loading impedance 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
If you are looking for an above average sounding cartridge for listening
and / or recording your vinyl then this would make a nice sounding cartridge for your
1/2" or P-mount system.
AUDIO-TECHNICA
AT-92ECD
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $49.99
includes "Real-Time, Real-Person" phone support for rebalancing and
re-adjusting your tone-arm's user adjustments if required or desired!
90 day full-price upgrade available on this model.
*(See
below for details)
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-3482P
P- MOUNT
TURNTABLE CARTRIDGE
for sale
An entry level Audio-Technica AT-3482P. Will fit turntables requiring a
"P-mount" cartridge. Definitely keeps a lid on the budget.
Features a Bonded Conical 0.7 mil Diamond stylus for tracking and
extended record life. Utilizes Audio-Technicas' own Vector-Aligned dual
magnet design for sonic generation.
Specs are as follows:
- Frequency Response: 20-20kHz
- Output strong 5 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-2.0 grams
- Recommended loading impedance 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
If you are looking for a cartridge for minimal listening to your albums,
not recording, your records are not in great shape or
of decent quality, your speakers are not too good and your budget will not bear the cost of the above
mentioned cartridges then this would make an 'OK' sounding cartridge for
your "P" mount turntable. (If you're looking to
do much recording "bite the bullet and spend a bit more money for
one of the above mentioned cartridges. The quality will be appreciably
better and given the amount of time you will invest in your recordings
the extra dollars spent at this time will be trivial over time.)
AUDIO-TECHNICA
AT-3482P
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $39.99
|
(click on above
thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
CN5625AL
"YELLOW"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for sale
An entry level Audio-Technica CN5625AL. Will fit turntables requiring a
1/2" standard mount cartridge. Definitely keeps a lid on the
budget. Features a Bonded Conical 0.7 mil Diamond stylus for tracking
and extended record life. Utilizes Audio-Technicas' own Vector-Aligned
dual magnet design for sonic generation.
Specs are as follows:
- Frequency Response: 20-20kHz
- Output strong 4.2 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-3.0 grams
- Recommended loading impedance 47K ohms (standard, requires only
standard phono pre-amp built-into most gear).
If you are looking for a cartridge for minimal listening to your albums,
not recording, your records are not in great shape or
of decent quality, your speakers are not too good and your budget will not bear the cost of the above
mentioned cartridges then this would make an 'OK' sounding cartridge for
your standard 1/2" mount turntable. (If
you have decent speakers / headphones / vinyl, or you're
looking to do much recording "bite the bullet and spend a bit more
money for one of the other cartridges
on this page, with an "elliptical" diamond stylus as opposed to this "conical"
model. The quality will be
appreciably better and given the amount of time you will invest in your
recordings and listening, the extra dollars spent
now will be trivial over
time.)
AUDIO-TECHNICA
CN5625AL
NEW
These are official
Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced
copies seen all over the internet and in on-line auctions
that simply look like the "real thing".
Our price $29.99
90 day full-price
upgrade available on this model. *(See
below for details)
|
|
- |
- |
- |
-----------------------------------------------------------------------------------------------------------------------
*90-DAY FULL PRICE TRADE IN
GUARANTEE ON NEW AT CARTRIDGE
upgrade details:
Purchase any one of the
* marked
1/2" or Universal cartridges listed above for your 1/2" turntable
and get our "90-DAY FULL PRICE TRADE IN GUARANTEE". That means
retain all the original packaging,
keep the cartridge / stylus in tip-top
condition and receive 100% of your original price paid to us (less S, H
& I charges) towards one of the higher priced
cartridges for an upgrade in performance! In order to qualify for this offer just contact
us with-in 90 days of placing your original order. Just give us a call
and we'll get you the details!
-----------------------------------------------------------------------------------------------------------------------
|
| |
Mount |
| |
Half-inch
|
P-mount
|
Universal
Fits both Half-inch
and P-mount |
| Stylus Tip |
| Conical |
CN5625AL |
AT3482P
- |
- |
| .4 x .7 elliptical |
AT95E
ATP-2XN
|
- |
- |
| .3 x .7 elliptical |
AT120E/T |
- |
AT92ECD
AT311EP |
| MicroLineTM
|
AT440MLa |
- |
- |
|
(click on above
thumbnails to enlarge photos)
NEW
-THE ULTIMATE-
AUDIO-TECHNICA
RECORD CARE KIT / CLEANER
for sale
No matter how good your turntable or cartridge is and
no matter what condition your albums are in, they will not sound good if
they are not clean! For LP's and EP's, the Audio-Technica, AT-6012 system is a great way to go. Clean records are also easier on your stylus
and can potentially reduce the risk of damage to speakers. Easy to use and
does a great job.
Kit includes the following:
- 'Sonic Broom' type Record cleaning brush
- Brush Storage base
- 2 oz. Audio-Technica Record Cleaning Fluid
Again if you are listening to vinyl and do not have a
way to consistently and easily clean you records, you are not getting the
most out of your records and system.
AUDIO-TECHNICA
RECORD CARE KIT
NEW
Our price $24.99*
*$24.99 price only when purchased with a
cartridge or one of our turntables
|
CLICK HERE FOR
PHONO / TURNTABLE / CARTRIDGE PRE-AMP
|
NEW ITEM
(click on above thumbnails to
enlarge photos)
ISOLATION FEET / SPIKES
SOLD METAL CONSTRUCTION
IN BRASS OR BLACK-CHROME
SET OF 4
FOR TURNTABLES AND OTHER COMPONENTS
for sale
These are great for isolating turntables, CD-Players, Speakers or any gear you
need replacement feet for, need to isolate due to
noise / vibration or wish to elevate from their shelf or floor.
LOOK KILLER! Sold in sets of 4. Come with double-side, rubber discs to
adhere them both the the bottom of gear and to adhere the bases to the
shelf or floor. Measure 1" in diameter and 1.25" to 1.5"
in height and weighs almost a pound!
Gold-Brass or Black-Chrome
NEW
$39.99 set of 4
|
|
|
CLICK ON A DEPARTMENT BELOW >
Wondering where
the "tone" you remember went?....
.... Surround yourself with Silver and find it again!
|
OUR PRIVATE LISTENING / AUDITIONING
SYSTEM
|
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
| SOLD
ITEMS BELOW: |
SOLD
ITEMS BELOW: |
SOLD ITEMS BELOW:
|
|
-
|
(click on above photos to enlarge)
NEW
AUDIO-TECHNICA
316
DISCONTINUED
UNIVERSAL
1/2" OR P-MOUNT
TURNTABLE CARTRIDGE
DISCONTINUED
|
DUAL CS-508 HEAD SHELL CARRIER |
| - |
-
|
-
|
