Categories

Home
Hi-Fi / Stereo Gear
Pro Audio
Microphones
Keyboard / Synths
Electric Guitars
Acoustic Guitars
Test Equipment
Beta / VHS VCRs
Film Equipment
Crosley Phones
Crosley Radios
Vintage Radios
Electric Fans
Retro Clocks
Retro / Deco
Jewelry Boxes
Aluminum Trees

Customer Care

Contact Us
Repair Resources
Restoration Steps
 

Purveyors of Electronic, Musical and Vintage goods from then, now and in between. 
Since 1982.

MICROPHONE CABLES / LEADS & CONNECTORS FOR VINTAGE / OLDER MICROPHONES
 

Vintage Microphone Cables / Cable / connectors / plugs for old 'Vintage' mics such as older / original Shure 55S, 55A, 55B, 55C, DY & EV Microphones & such as EV / Electrovoice 664, 644, 611, 623, 630, 676, 726, 911 Mercury Mics / Mikes. Old microphone Cables / cords / wires w/ Amphenol 3-pin, 4-pin, 91-MC3M, 91MC3M, 91-MC4M, 91MC4M connectors. Center pin connectors & shielded microphone cables, for Turner 22A, 33, 33D, 22D, Rauland 1248, Astatic JT-30, 77A. Some connectors will also fit 'Collins' amateur / ham radios / mics.
  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)
 



VINTAGE MICROPHONE CABLES / LEADS:

 

 
CABLES FOR VINTAGE MICS!



(Click on above thumbnails to enlarge photo)

MODEL - 91-MC3M - XLR
aka: '3-Pin to XLR'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/
ORIGINAL NEW OLD STOCK
3-PIN - MALE XLR
AMPHENOL
SCREW-ON CONNECTOR
MICROPHONE CABLES

MADE IN THE USA!

VINTAGE STYLE MICROPHONE CABLES FOR SALE
New vintage mic cables for mics utilizing screw-on, 3-pin Amphenol type connectors. These are super-high quality cables with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol type 3-pin screw-on connector on one end, and an all metal male XLR connector on the other for input to standard, modern mixers with XLR inputs. To use with a guitar amp input, simply use an adaptor!
T
hey will fit Astatic 77, early issue / original / discontinued series Shure,
55S, 55C, 55B, early issue / original / discontinued 55 series, PE55, 55SW, 51, 51S, 315, 530, 535, 556, 705 / 705A, DY-11, DY-45G, University Sound 5050, and others,  some older / early / original issue EV microphones such as the EV 630, EV-726, 731 Cardyne II, (may require slight modification to connector on cable) (note: Shure microphones with '3-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "3-Pin" connectors for EV mics). Turner 22X, Turner U9S (no mod required), Stromberg-Carlson MC41, MD22A, and others utilizing a 3-pin, screw on Amphenol type (not for modern mics utilizing XLR connectors).
Please verify that your microphone is working prior to ordering. If you need assistance doing this please just phone us.
20' (feet) in length!
New!

JUST IN!!!
WE HAVE A VERY SMALL, AND LIMITED QUANTITY OF THESE BACK IN STOCK.

$89.99 plus shipping
"Buy Now" button currently only applicable for shipping within the US states.

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


CABLES FOR VINTAGE MICS!

(Click on above thumbnails to enlarge photo)

MODEL - 91-MC4M - XLR
aka: '4-Pin to XLR'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/
ORIGINAL NEW OLD STOCK
4-PIN - MALE XLR
AMPHENOL
SCREW-ON CONNECTOR
MICROPHONE CABLES

MADE IN THE USA!

VINTAGE STYLE MIC CABLE FOR SALE
New vintage mic cables for many (not all)  EV (Electro-Voice)  mics utilizing screw-on, 4-pin Amphenol type connectors. These are super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol type 4-pin screw-on connector on one end, and an all metal, male XLR connector on the other for input to standard, modern mixers with XLR inputs. To use with a guitar amp input, simply use an XLR-1/4" adaptor!
They will fit DuKane 7A160, EV / Electrovoice 77A, EV-
623 / Exectutone EXL, EV 630, 636, 644, 664, 674, 676, EV-726, 767, Rauland 1248, Stromberg-Carlson MD37CS and most other EV utilizing a 4-pin, screw on Amphenol type.

These will also fit, with a slight modification to the plug, some early / original issue Shure mics such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "4-Pin" connectors for Shure mics).


> Have a Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' and want one WITHOUT the "modification"? As of 3/2/2020, we have a 'handful' of the 'proper' connectors for an
additional $25. Just give us an email or phone call for further info or to order. <

Please verify that your mic is functioning prior to ordering cables. If you need assistance doing this please just phone us.
20' (feet) in length!
NEW!

VERY
SMALL, LIMITED QUANTITY REMAINING

$89.99 plus shipping
"Buy Now" button currently only applicable for shipping within the US states.

 

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

CABLES FOR VINTAGE MICS!



(Click on above thumbnails to enlarge photo)

MODEL - 91-MC3M - 280
aka: '3-Pin to 1/4'
CABLES FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/
ORIGINAL NEW OLD STOCK
AMPHENOL
SCREW-ON
        3-PIN TO MALE 1/4" / 280 / PHONO / GUITAR PLUG
MICROPHONE CABLES

MADE IN THE USA!

VINTAGE STYLE MIC CABLE FOR SALE
New vintage mic cables for microphones utilizing screw-on, 3-pin Amphenol type connectors. These were originally known as Shure "C5-3" Cable and Plug assemblies". These are super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol type, 91-MC3M, 3-pin screw-on connector on one end, and an all metal 1/4" male "guitar / phono" plug connector on the other for input to standard guitar amps and mixers with 1/4" inputs.
T
hey will fit Astatic 77, early issue / original / discontinued series Shure,
55S, 55C, 55B, early issue / original / discontinued 55 series, PE55, 55SW, 51, 51S, 315, 530, 535, 556, 705 / 705A, DY-11, DY-45G and others,  some older / early / original issue EV microphones such as the EV microphones such as the EV 630, EV-726, 731 Cardyne II, (may require slight modification to connector on cable)
(note: Shure microphones with '3-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "3-Pin" connectors for EV mics). Turner 22X, Turner U9S (no mod required), Stromberg-Carlson MC41, MD22A, and others utilizing a 3-pin, screw on Amphenol type (not for modern mics utilizing XLR connectors).
Please verify that your mic is functioning prior to ordering cables. If you need assistance doing this please just phone us.
20' (feet) in length!
NEW!

JUST IN!!!
WE HAVE A VERY SMALL, AND LIMITED QUANTITY OF THESE BACK IN STOCK.


$85.99 plus shipping


(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
  

(Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

CABLES FOR VINTAGE MICS!



(Click on above thumbnails to enlarge photo)

MODEL - 91-MC4M - 280
aka: '4-Pin to 1/4'
CABLES
FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
CUSTOM BUILT
W/
ORIGINAL NEW OLD STOCK
AMPHENOL
SCREW-ON
        4-PIN TO MALE 1/4" / 280 / PHONO / GUITAR PLUG
MICROPHONE CABLES

MADE IN THE USA!

VINTAGE STYLE MICROPHONE CABLES FOR SALE

New vintage mic cables for EV Electro-Voice microphones and other utilizing screw-on, 4-pin Amphenol type connectors. These are super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol type, 91-MC4M, 4-pin screw-on connector on one end, and an all metal 1/4" male "guitar / phono" plug connector on the other for input to standard guitar amps and mixers with 1/4" inputs.
They will fit DuKane 7A160, EV / Electrovoice 77A, EV-
623 / Exectutone EXL, EV 630, 636, 644, 664, 674, 676, EV-726, 767, Rauland 1248, Stromberg-Carlson MD37CS and most other EV utilizing a 4-pin, screw on Amphenol type.


These will also fit, with a slight modification to the plug, some early / original issue Shure mics such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "4-Pin" connectors for Shure mics).

Have a Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' and want one WITHOUT the "modification"? As of 3/2/2020, we have a 'handful' of the 'proper' connectors for
an additional $25. Just give us an email or phone call for further info or to order.

Please verify that your mic is functioning prior to ordering cables. If you need assistance doing this please just phone us.
20' (feet) in length!
NEW!


VERY
SMALL, LIMITED QUANTITY REMAINING

$85.99 


(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

 (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 
CABLES FOR VINTAGE MICS!

(Click on above thumbnails to enlarge photo)

MODEL: "F-XLR"

CABLE FOR VINTAGE MICS, HARP MICS, AMPS AND LAPSTEELS!
"RARE AS HENS' TEETH"
CUSTOM MADE

CENTER PIN - MALE XLR
MICROPHONE CABLE
2501F
SCREW-ON TYPE MICROPHONE PLUG TO MALE XLR / A3M PLUG
MADE IN THE USA!


New vintage mic cables for many older mics utilizing screw-on, center-pin Amphenol connectors ~5/8" in diameter. These are super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol center-pin screw-on connector on one end, and an XLR male connector on the other for input to standard modern mixers and snakes.  To use directly into a guitar amp simply use an adaptor, transformer, or direct box.
They will fit any microphone, pick-up, or any device utilizing a center-pin, screw on Amphenol type including Astatic JT-30, Turner S22D, 22X, and Turner 33D, some Americans, some
vintage / original issue / discontinued Shure microphones such as the 535A, PE-585 PE585, some "PE" series, some 'Slim-X' series, such as the 777S
microphones, vintage / original issue / discontinued EV 606, EV 611 Mercury, EV 911 Mercury, EV 630, EV 638, EV Cardax 950, EV-726 / CARDYNE I/II / 1/2, some Altec Microphones, American Microphones, Calrad DM-11, Calectro QA-150, and many, many others. (not for modern XLR mics). Please verify that your mic or pickup is functioning prior to ordering cables (not for modern mics utilizing XLR connectors).
If you need assistance doing this please just phone us.
20' (feet) in length!
NEW!
$48.99 ea.

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.)

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

 

CABLES FOR VINTAGE MICS!

(Click on above thumbnails to enlarge photo)

MODEL: "F-TWENTY"

CABLE FOR VINTAGE MICS, HARP MICS, AMPS AND LAPSTEELS!
"RARE AS HENS' TEETH"

CENTER PIN -1/4" GUITAR / PHONO STYLE PLUG
MICROPHONE CABLE
2501F
SCREW-ON TYPE MICROPHONE PLUG TO MALE 1/4" / 280 / PHONO / GUITAR PLUG
MADE IN THE USA!


New vintage mic cables for many older mics utilizing screw-on, center-pin Amphenol connectors ~5/8" in diameter. These are super-high quality cable with a great 1 year warranty from manufacturer. They are well insulated and shielded, with an Amphenol center-pin screw-on connector on one end, and an all metal 1/4" male "guitar / phono" plug connector on the other for input to standard, modern mixers and guitar amps with 1/4" inputs. 
They will fit any microphone, pick-up, or any device utilizing a center-pin, screw on Amphenol type including Astatic JT-30, Turner S22D, 22X, and Turner 33D, some Americans, some
vintage / original issue / discontinued Shure microphones such as the Shure 533SA and 533SB Spher-O-Dyne, Shure 535A, PE-585 PE585, some "PE" series, some 'Slim-X' series, such as the 777S
microphones, vintage / original issue / discontinued EV 606, EV 611 Mercury, EV 911 Mercury, EV 630, EV 638, EV Cardax 950, EV-726 / CARDYNE I/II / 1/2, some Altec Microphones, American Microphones, Calrad DM-11, Calectro QA-150, and many, many others (not for modern mics utilizing XLR connectors).
Please verify that your mic is functioning prior to ordering cables. If you need assistance doing this please just phone us.
 20' (feet) in length!
NEW!
$42.99 plus shipping
"Buy Now" button currently only applicable for shipping within the US states.

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.)

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

(Click on above thumbnails to enlarge photo)

SUPER QUALITY
25'
STANDARD 3-PIN 
FEMALE XLR - MALE XLR
LOW IMPEDANCE MIC CABLE
OUR PART # SJ-25
MADE IN THE USA!
&
WITH A LIFE-TIME WARRANTY*


Cable for modern XLR mics such as EV N/D 257, 357, 457, 757, PL Series, EV DS35, 635, RE-38, RE-10, RE-20, AKG  C-3000, C-1000, 414, D-190E, D-1000, D-1200E and hundreds of other models. If your mic uses utilizes an XLR connector then this cable will work. These are not "Cheap" cables. I do not use or sell "Cheap" cables. If your number one priority is to save money, in the short run, then that's what you should do. Save your money. If you want to buy a mic cable you can finally rely on show after show, then THIS IS THE CABLE!!! I have sold literally thousands of these and have only had maybe a dozen come back. They are fitted with the more expensive Switchcraft brand plugs on both ends and are hand made in the USA with a LIFETIME warranty!
* If it fails due to workmanship or parts failure, just send it back and it will be repaired or replaced with a new comparable unit!*  Just send it back and we'll either repair it or at our option, send you a new one.* Your show is important. Too important to trust to cheap, intermittent cables. I can't tell you how many times I have seen a $30,000 sound system brought to it's knees by one $3 cable.
NEW
$24.99 ea.

 or

Get a 6-pack for
$204.99 shipped**


* Warranted against defects in original workmanship, but not against abnormal use / abuse, ie; cut cable, bent plug or cables eaten by dogs, cats or other family members.

**Shipping to lower 48 US states. Other locations calculated separately.
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)




      

(Click on above thumbnails to enlarge photo)

REAL QUALITY
6" (inch)
   FEMALE XLR  -  1/4" MALE
LOW IMPEDANCE to HIGH Z
MIC ADAPTOR / TRANSFORMER / PIGTAIL


Finally we found an XLR-1/4" transformer / adaptor that doesn't "gut" itself after you use it a half dozen times. I can't tell you how many times I've used cheap versions of these in the past at gigs, that totally come apart when you un-plug them. This one is built to last and stay together. 
This version is also the "pig-tail" one that doesn't turn your microphone cable plug into an '8" lever' like the "solid" versions do. With the cheap way mixing boards / consoles, portable PA systems and guitar amps are made these days, you need all the help you can get. Any tension on the solid, "one-piece" versions will bend your input jacks and stress the 'direct to circuit board' solder connections. This version puts no more tension on your input jacks than a normal cable does. 
Internal, built-in transformer converts Low Z (600 ohms) to Hi Z (50,000 ohms) to allow all your mic's sound into your pre-amp / amp. It's essentially a Direct-Box in a cable. 1 year warranty against workmanship defects
*.
NEW

$34.99 ea.

Sorry, but now discontinued as of 8/6/18

* Warranted against defects in original workmanship, but not against abnormal use / abuse, ie; cut cable, bent plug or cables eaten by dogs, cats or other family members.

**Shipping to lower 48 US states. Other locations calculated separately.
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)




(Click on above thumbnails to enlarge photo)

SUPER QUALITY
20'
STANDARD 3-PIN 
XLR-1/4" PHONO / 280 PLUG
HIGH IMPEDANCE MIC CABLE
OUR PART # M-20
MADE IN THE USA!
&
WITH A LIFE-TIME WARRANTY*


Cable for modern XLR mics that are High-Impedance. These are not "Cheap" cables. I do not use or sell "Cheap" cables. If your number one priority is to save money, in the short run, then that's what you should do. Save your money. If you want to buy a mic cable you can finally rely on show after show, then THIS IS THE CABLE!!!  They are fitted with the more expensive Neutrik brand plugs on both ends and are hand made in the USA with a LIFETIME warranty!
*  If it fails due to workmanship or parts failure, just send it back and it will be repaired or replaced with a new comparable unit!*  Just send it back and we'll either repair it or at our option, send you a new one. Your show is important. Too important to trust to cheap, intermittent cables. I can't tell you how many times I have seen a $30,000 sound system brought to it's knees by one $3 cable. Again, these cables are for High-Impedance mics. (If you have a normal Low-Impedance mic and wish to connect to a 1/4" jack, then you should choose our SJ-25 XLR-XLR cable with our XLR-1/4" Transformer converter.)
NEW
$39.99 ea. 


  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 





(Click on above thumbnails to enlarge photo)

SUPER QUALITY
20'
STANDARD 3-PIN 
XLR-1/4" PHONO / 280 PLUG
HIGH IMPEDANCE MIC CABLE
OUR PART # V-20
MADE IN THE USA!
&
WITH A LIFE-TIME WARRANTY*


Cable for modern EV Electro-Voice XLR mics that are High-Impedance. These are not "Cheap" cables. I do not use or sell "Cheap" cables. If your number one priority is to save money, in the short run, then that's what you should do. Save your money. If you want to buy a mic cable you can finally rely on show after show, then THIS IS THE CABLE!!!  They are fitted with the more expensive Neutrik brand plugs on both ends and are hand made in the USA with a LIFETIME warranty!
*  If it fails due to workmanship or parts failure, just send it back and it will be repaired or replaced with a new comparable unit!*  Just send it back and we'll either repair it or at our option, send you a new one. Your show is important. Too important to trust to cheap, intermittent cables. I can't tell you how many times I have seen a $30,000 sound system brought to it's knees by one $3 cable. (If you have a normal Low-Impedance mic and wish to connect to a 1/4" jack, then you should choose our SJ-25 XLR-XLR cable with our XLR-1/4" Transformer converter.)
NEW
$39.99 ea. 


  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

Amphenol_3-Pin_Male_91-MC3M_conn_Pair_web.jpg (28435 bytes)     Amphenol_3-Pin_Male_91-MC3M_exploded_web.jpg (16466 bytes)

(Click on above thumbnails to enlarge photo)

MALE 91-MC3M / 91MC3M 

CONNECTORS FOR VINTAGE MICS!
"RARE AS HENS' TEETH"
ORIGINAL / NEW OLD STOCK
AMPHENOL
3-PIN MICROPHONE CONNECTOR
MALE 91-MC3M / 91MC3M 
CABLE MOUNT MICROPHONE CONNECTORS
MADE IN THE USA!

VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New "Amphenol" style 3-pin 91-MC3M Microphone cable connectors. 
T
hey will fit Astatic 77, early issue / original / discontinued series Shure,
55S, 55C, 55B, early issue / original / discontinued 55 series, 55SW, 51, 51S, 315, 530, 535, 556, 705 / 705A, DY-11, DY-45G and others,  some older / early / original issue EV microphones such as the EV 630, EV-726, 731 Cardyne II, (may require slight modification to connector on cable)
(note: Shure microphones with '3-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "3-Pin" connectors for EV mics). Turner 22X, Turner U9S (no mod required), Stromberg-Carlson MD22A, and others utilizing a 3-pin, screw on Amphenol type (not for modern mics utilizing XLR connectors).

This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy Suitcase" Reel to Reel player / Recorder for signal in and out to the Record / Play head.
(We do not have any technical info at this time, but would assume, based on other mfg's use of 'Pin-1' that it would be 'Ground' and that the other two pins would be 'In & Out', but we have no info as to which. Those pins likely go directly to the 'Tape Head' as it does not appear that the unit has a 'Record / Playback Amplifier' built in, but that's all speculation at this point).

 They are available in very limited quantities and when they're gone we don't know when we will have access to more. 

SORRY, NOT SELLING SEPARATELY NOW, ONLY AS 'CABLE ASSEMBLIES'

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 


 

 

4-Pin_Amphenol_Vintage_Microphone_Mic_Connector_web.jpg (39095 bytes)

(Click on above thumbnails to enlarge photo)


 MALE 91-MC4M  / 91MC4M 

"RARE AS HENS' TEETH"
ORIGINAL / NEW OLD STOCK
AMPHENOL
4-PIN MICROPHONE CONNECTOR
CABLE MOUNT MICROPHONE CONNECTORS
MADE IN THE USA!
VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4M Microphone cable connectors. 
They will fit
DuKane 7A160, some some older / early / original issue EV models 77A, 623 / Exectutone EXL, 636, 644, 664, 674, 676, 726, 767 and others, Rauland 1248, Stromberg-Carlson MD37CS microphones and others utilizing a 4-pin, screw on Amphenol type connector.

These will also fit, with a slight modification to the plug, some early / original issue Shure mics such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "4-Pin" connectors for Shure mics).

Have a Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' and want one WITHOUT the "modification"? As of 3/2/2020, we have a 'handful' of the 'proper' connectors for an additional $25. Just give us an email or phone call for further info or to order.


This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy Suitcase" Reel to Reel, player / Recorder for power from the rechargeable battery pack, Stancil Hoffman BC-9C
(w/ 'Pin-1' most likely being ground, and 'Pin-4' likely positive, but that's 'educated speculation' based on every other mfg's 'Pin-1' utilization. Pins 2 & 3 do not appear to be utilized on the power port.)


SORRY, NOT SELLING SEPARATELY NOW, ONLY AS 'CABLE ASSEMBLIES'

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 


(Click on above thumbnails to enlarge photo)

GOLD ANODIZED / PLATED 
MALE 91-MC4M 
/ 91MC4M 

"RARE AS HENS' TEETH"
ORIGINAL / NEW OLD STOCK
AMPHENOL
4-PIN MICROPHONE CONNECTOR
CABLE MOUNT MICROPHONE CONNECTORS
MADE IN THE USA!

VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4M Microphone cable connectors. 
They will fit
DuKane 7A160, some some older / early / original issue EV models 77A, 623 / Exectutone EXL, 636, 644, 664, 674, 676, 726, 767 and others, Rauland 1248, Stromberg-Carlson MD37CS microphones and others utilizing a 4-pin, screw on Amphenol type connector.

These will also fit, with a slight modification to the plug, some early / original issue Shure mics such as the Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' microphones (not for modern mics utilizing XLR connectors).
(note: Shure microphones with '4-pins' always have 'Pin-1' / ground 'in-line', or 'adjacent' to the key slot, where EV has "Pin-1" skewed a few degrees from it. Just FYI and again, why we have to modify most of the "4-Pin" connectors for Shure mics).

Have a Shure 545, 545S, 565 / 565S / PE54-II Unidyne-III Dynamic, Uni-Sphere / 'Pistol Grip' and want one WITHOUT the "modification"? As of 3/2/2020, we have a 'handful' of the 'proper' connectors for an additional $25. Just give us an email or phone call for further info or to order.


This connector was also used on the 'Stancil Hoffman' "MiniTape / Spy Suitcase" Reel to Reel, player / Recorder for power from the rechargeable battery pack, Stancil Hoffman BC-9C
(w/ 'Pin-1' most likely being ground, and 'Pin-4' likely positive, but that's 'educated speculation' based on every other mfg's 'Pin-1' utilization. Pins 2 & 3 do not appear to be utilized on the power port.)


Includes strain relief inside (not visible in photos). While this does have some cosmetic wear, as it's about 60 years old, it is NOS.

$89.99
ONLY 1 FOR SALE

(2 in stock, but I'm keeping one for my personal, Gold EV-664)


(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables) 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)

 

 

 

PHOTOS COMING

3-PIN MALE MICROPHONE CONNECTOR
AMPHENOL
91-MC3M1

"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT91-MC3M1-W/OC
(without collar)
MADE IN THE USA!

No, we don't know what these fit, so study the photos and your mic or connector closely.

VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin MALE 91-MC3M1 Microphone cable connectors. 
They are in limited quantities and when they're gone we don't have a source more. We do not know what mics / connectors they will fit, so look VERY CLOSELY and STUDY the above photos.
They are not for standard, early / original issue / vintage Shure mics such as the Shure 55
series, 51, 500, 315 etc. (we do not have that connector separately, only as a complete cable) but they do use the same 91-MC3M Amphenol Pin configuration of Pin-1 directly under the keyway. These are in very limited quantities and when they're gone, they're gone (not for modern mics utilizing XLR connectors).
91-MC3M1 NOS
$44.99 ea. 

ONLY ABOUT A DOZEN LEFT IN STOCK


If anyone has any info as to models these connectors fit or proper model number feel free to let us know. Thanks.
 

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 


 

EV_Amphenol_91-MC4F_Collared_4-Pin-Female_Microphone_connector_collage.jpg (126668 bytes)

(Click on above thumbnails to enlarge photo)

4-PIN FEMALE MICROPHONE CONNECTOR
AMPHENOL
91-MC4F

"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
CABLE MOUNT MICROPHONE CONNECTORS /
EV 664 REPLACEMENT INSERT CONNECTOR

OUR PART # OT4F-W/C (with collar)
MADE IN THE USA!

No, we don't know what these fit, so study the photos and your mic or connector closely.

VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 4-pin 91-MC4F? microphone cable connectors.   They are in limited quantities and when they're gone we don't have a source more. We do not know what mics or connectors they will fit, so look VERY CLOSELY and STUDY the above photos. (We have determined that they will fit Astatic DNHZ 's & D-104 's. They may also fit others)
Just figured out that the inside, bakelite part of this will replace your broken / busted / chipped internal connector on EV mics with 4-pins, such as the EV 664!  (not for modern mics utilizing XLR connectors).
We have actually repaired a few EV 664's with the insert from this connector.

NEW
$44.99 ea. 

IN STOCK


If anyone has any info as to other models these connectors fit or proper model number feel free to let us know. Thanks.

These connectors
will fit Astatic DNHZ 's & D-104 's microphones mics
 

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 




 



"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
3-PIN FEMALE 91-MC3F
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT91-MC3F-W/C (with collar)
MADE IN THE USA!
No, we don't know what these fit, so study the photos and your mic or connector closely.

VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin FEMALE 91-MC3F Microphone cable connectors. They are in limited quantities and when they're gone we don't have a source more. Beyond some American mic models such as the American D5, D9 and variations, do not know what mics or connectors they will fit, so look VERY CLOSELY and STUDY the above photos. 
They are not for standard, early / original issue / vintage Shure mics such as the Shure 55 series, 51, 500, 315 etc. (we do not have that connector separately, only as a complete cable) but they do use the same 91-MC3M Amphenol Pin configuration of Pin-1 directly under the keyway (not for modern mics utilizing XLR connectors).  These are in very limited quantities and when they're gone, they're gone. 
NOS 91-MC3F
$64.99 ea. 
ONLY A ONE
LEFT IN STOCK

If anyone has any info as to models these connectors fit or proper model number feel free to let us know. Thanks.
 

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 


PHOTOS COMING


"EVEN RARER THAN HENS' TEETH"
ORIGINAL NEW OLD STOCK
AMPHENOL
3-PIN FEMALE 91-MC3F1
CABLE MOUNT MICROPHONE CONNECTORS
OUR PART # OT3F-W/OC
(without collar)
MADE IN THE USA!

These will couple with a standard 91-MC3M connector. We don't know what else it will fit.
VINTAGE STYLE MICROPHONE MIC CONNECTORS FOR SALE
New old stock Amphenol 3-pin FEMALE 91-MC3F1? Microphone cable connectors. There is very limited supply of this style connector. We do not know what mics or connectors they will fit, so look VERY CLOSELY and STUDY the above photos. 
They are not for standard, early / original issue / vintage Shure mics such as the Shure 55 series, 51, 500, 315 etc. (we do not have that connector separately, only as a complete cable), but they do use the same Amphenol 91-MC3M Pin configuration of Pin-1 directly under the key and will mate up with our standard 3-Pin Shure / Amphenol 91-MC3M cable connectors (not for modern mics utilizing XLR connectors). These are in very limited quantities and when they're gone, they're gone. 
NOS 91-MC3F1?
$44.99 ea. 


SOLD OUT

If anyone has any info as to models these connectors fit or proper model number feel free to let us know. Thanks.

New info; We have been informed that this connector possibly fits the Astatic T-3 microphone.
 

(As many of the connectors for 'vintage mics' are 'vintage / NOS' as well, they have likely been around for 30-60 years, and may show some surface corrosion / tarnish / scuffing, but this will only be cosmetic and will not affect performance. Cables / wire are new / fresh stock as well as the 280 & XLR plugs.
ALSO, be aware that many of the connectors out there on the web are MISSING their 'strain relief' clips. These are 'internal' parts that many sellers are not aware of, nor are aware that may be missing. Without internal strain relief for the cable, you will need to 'fabricate' adequate internal clamping / strain relief, or you'll be re-doing the wire / solder connections quite often. About half the connectors I receive are missing their original strain relief clips. Fortunately we have a decent 'supply' of them to add to our connectors prior to building the cables)
 

  (Above text, in it's entirety, including 'fit list' property of www.oaktreevintage.com / Oak Tree Enterprises, LLC. See 'Copyright Information' page for details)


 

 


________________________________________________________________________

"Hey Jerry, The cable arrived today and works like a charm! Happy to be able to use that great mic now! Thank you for your service! All the best!" Arnout, in Belgium
________________________________________________________________________

"
Hi Jerry, Just wanted to say a word of thanks for your great service with my purchase of the 4 pin cable for my EV Slim Air mic. The mic is working well and I’m excited about future recordings with it. The delivery was quick and quality product."
All the best, Patrick D.,  Vancouver Canada
________________________________________________________________________

"I just wanted you to know that the cable you (built and) sent is great and my vintage Shure PE54 sounds very nice and performs flawlessly! Thanks So Much Tim L.",
________________________________________________________________________

"
Hi, Jerry, The 3 cables that you made for me arrived…and now the microphones are all happy and sounding awesome. Thanks again, Jim" Modern Art Music Image + Music + Words www.jimwardmorris.com  - California
________________________________________________________________________


"Hi, I received my 91-MC3M to XLR cable today. Excellent!!  I 'rolled the dice' on whether my Elvis Fat Boy (mic) worked or not. Plugged it in with the new cable and there it was - wonderful sound. Elvis would be proud!! Thank you for a wonderful job and fast delivery. Cable is perfect!! John S." - Illinois
________________________________________________________________________


"Thanks for the microphone cable (F-20). Very nicely made - I especially appreciate the strain-reliefs. Nice to order a product that is carefully constructed." - Murray N. California
________________________________________________________________________


"Hello! I recently ordered a (vintage) microphone cable for my Electro-Voice microphone; I haven't had a cable for it in 28 years! I got the cable in less than a week, screwed it onto the microphone and it worked great! I'm thrilled that I was able to find the cable and get it so easily! Thanks for great service; I'm recommending you to all my friends and colleagues! Best" - Alan - Verona, WI.
________________________________________________________________________

I got it (cable for the vintage Shure Microphone) and it works very well! Thanks :-) - Gerald, Tacoma, WA
________________________________________________________________________

"Hello Jerry, We have received the cable (vintage mic cable) today, it works and sounds great. Thank you." Gal, The Netherlands.
________________________________________________________________________

"Hi Jerry, I just wanted to let you know that the cable arrived yesterday, and everything works like a charm.... And my wife says "thanks" for the Tootsie Rolls !! It was great doing business with you... I'll pass your name along to anyone who might benefit from your services. Thanks again," - Brendon in Canada  
________________________________________________________________________

"Jerry, Received the F-20-XLR cable today ... and the candy ... thanks! Thanks for your help." - Bob C., Grand Prairie, Texas 
________________________________________________________________________

"Dear Sirs:  It was only two days ago I called and ordered your 3-pin Amphenol cables to fit my vintage Shure 55-C's.  I already have the package, the cables are EXACTLY what I was after and I just wanted to say how pleased I was with the total overall experience!  Thanks," - Ed Burnette   
________________________________________________________________________

"Hi Jerry, Just a note to let you know that the cable arrived safely today. Thanks very much for expediting the shipping. It will definitely come in handy. I'm very glad to have found your site." - Kevin P.
________________________________________________________________________

"Just wanted to say thanks for the center pin to screw-on F-20 to 1/4" cable. Perfect for hooking up my bass to my old Bogen tube PA!" - John W.

 


These cables and / or connectors are not made by any of the above listed "Microphone Manufacturers". Brands listed above are protected trademarks / properties of the respective companies mentioned. Oak Tree Enterprises, LLC is not affiliated with any of the above "Microphone" companies.
Sorry, but we do not have cables for most of the 'Japanese' built mics from the 1950's, 1960's, or 1970's, including the
AUDIOTEX / GC, CALECTRO Q4-150, Calrad DM-11, DM-15, DM-16H.L, Kay TM-4, Kent DM-13, Lafayette, RCA HK-102, microphones, etc.

For more...


 
 







TO SEE OTHER VINTAGE MICROPHONES WE HAVE FOR SALE CLICK HERE








 
-
-
-
 


 

LINKS TO OUR 'HI-FI' DEPARTMENTS

Amps and
Pre-Amps

Receivers

Cassette
Decks

Tuners

Turntables

8-Track Decks

CD Players

Reel-Reel
Decks

EQs and Signal
Processors

Speakers

Betamax and
VHS VCRs

Turntable Cartridges

Tube Audio

Ne'cessories

Speaker Parts

Record Players

Vintage Radios

Vintage
Walkmans

Headphones

Stereo Parts


Wondering where the "tone" you remember went?....


 

.... Surround yourself with Silver and find it again!


CONTACT INFO BELOW

$20. MINIMUM ORDER

 

                                             

IF YOU PREFER TO PLACE YOUR ORDER FOR THE ABOVE PARTS / ACCESSORIES BY PHONE,
PLEASE CALL US AT:

(800) 806-4231
- Press Option '2' for 'SALES' to order -

NOT the 'Parts / #1' option

OR EMAIL
sales@oaktreevintage.com

~10:00 AM- ~5:30 PM most days COLORADO / ROCKY MOUNTAIN TIME ZONE


ALSO: When e-mailing be sure to include a relevant subject, ie: Brand / Model number / reason for inquiry in the 'SUBJECT LINE'.
SUBJECT
lines left empty, or with 'single word' text like;
"Hello", "Hi", "parts", "stereo", "inquiry", "question", "selling" or similar or similar 'un-qualified' terms will automatically be deleted by Anti-Virus / Spam settings or receive 'Low Priority'.
(Subject lines left empty show up as "No Subject" and are deleted automatically by our anti-spam settings"


 SPEAKER PARTS   |   STEREO / HI-FI ELECTRONIC PARTS   |  KEYBOARD PARTS 

___________________________________________

Haven't received a response to your email? See FAQ'S

MAILING:
OAK TREE ENTERPRISES
PO. BOX 6182
COLORADO SPRINGS, CO 80934
U.S.A
.

Before ordering by postal mail, please phone or email us about the item and the details of sending your funds. Thank-you.


 SPEAKER PARTS   |   STEREO / HI-FI ELECTRONIC PARTS   |   SELLING-TRADING-CONSIGNING   |  KEYBOARD PARTS   I   FAQ'S  
  CONDITION RATINGS   |   ORDERING / POLICIES    |    WARRANTIES / RETURNS   |   SHIPPING     
 RESTORATION PROCEDURES   |   REPAIRS  | CONTACT PARTS


30% restock fee / service charge applies to all 'parts' returns for refund.
Some parts are not returnable.

See our "
Warranties / Returns" page via the link below for more details.


POLICIES, SPECIFICATIONS, AVAILABILITY, INFORMATION AND PRICING SUBJECT TO CHANGE  AT ANYTIME  AND WITHOUT PRIOR NOTICE
and changes may not be posted to web immediately
. Information such as Parts Substitution possibilities, "Circa" dates, original values, etc. are to the best of our knowledge. If you are critically concerned, you should do independent
research on your own prior to ordering or utilizing this information in any way. Manufacturers also are known to change part numbers, specs, circuit designs, specs etc within the same model.
 

Copyright © 1997-2023 Oak Tree Enterprises, LLC

COPYRIGHT INFORMATION